Showing results: 2911 - 2925 of 3393 items found.
-
Optical Zonu Corp.
Optical Zonu’s RF over Fiber product line contains multiple stand-alone modules which are designed to integrate easily with your application. Each of our stand-alone modules is a Transceiver (TRx), but it may also be configured as individual Transmitter (Tx) or Receiver (Rx) units. A pair of these transceivers creates two-way bidirectional RF to Optical and Optical to RF link. Standard operational frequency ranges between 47 MHz and 3 GHz but can be extended to from 10 KHz to 3.3 GHz. OZ816 and OZ1606 modules have ultra-broadband capability that ranges from 47MHz to 7 GHz.
-
450 -
Oersted Technology
The Model 450 is a high-resolution, laboratory gaussmeter, capable of measuring magnetic fields from 0.001 Gauss to 300k Gauss (measurement range is dependent on probe used). This unit is designed for demanding applications, such as material analysis and field mapping, where low-noise, high-resolution magnetic measurements are necessary. Measurements of AC and DC magnetic fields are shown in Gauss or Tesla on the two-line vacuum fluorescent display. The Model 450 features RS232C and IEEE-488 ports, allowing the instrument to be controlled via a remote computer or automation equipment. A hall-effect gaussmeter probe is included with the Model 450, and may be selected from an extensive line of probe
-
Imaginant Inc.
Utilizing optical and semiconductor fabrication techniques, Imaginant manufactures the PureView PrecisionTM line of RoHS-compliant delay-line ultrasound transducers with center frequencies ranging from 50 MHz to 250 MHz (higher and lower transducer frequencies are also available). Imaginant's precision-manufacturing process produces transducers that exhibit high reliability and high uniformity from device to device. This manufacturing consistency enables uniform test system performance to be attained across multiple systems. Imaginant transducers are available in focused and flat-face models that can be produced with minimal-damping for applications requiring maximal sensitivity or with maximal-damping and high-bandwidth for applications requiring the highest-degree of temporal precision.
-
Stack-Match II -
Array Solutions
Stack Match controller is a replacement for the rotary switch Stack Match controller. It features pushbutton switches for easy antenna selection and has outputs for both phase control and an auxiliary output. It is a component of the ShackLAN product line and as such can be fully remotely controlled via computer with our ShackLAN Control Center software. All outputs are switched with relay contacts for maximum reliability and power for the external switching unit may be applied from a separate power source to provide maximum isolation from the ShackLAN network. There is also a PTT input to allow different stack configurations for transmit and receive.
-
StackMatch -
Array Solutions
The StackMatch control switch box has a rotary switch and three LEDs which display the antennas selected. Think of the three LEDs as the antennas arranged on a tower with number 3 in the ▲ being at the top of the tower, number 2 in the ● being in the middle, and number 1 in the █ at the bottom of the stack. As the rotary switch is turned these LEDs will light up in a pattern which indicates which antennas are being fed power from the StackMatch. You will see these symbolsalso on "little towers" or lines arranged around the rotary switch knob. Just point the knob to the desired pattern and the LEDs will light to indicate in the same pattern as chosen with the switch.
-
PXI-2022 -
ADLINK Technology Inc.
ADLINK"s PXI-2022 is a simultaneous-sampling multi-function DAQ card to meet a wide range of application requirements for PXI bus computers. The device can simultaneously sample 16 AI channels with differential input configurations in order to achieve maximum noise elimination. If more analog input channels are required, multiple cards can be synchronized through the PXI Trigger bus. The PXI-2022 features digital triggering, 4-CH programmable digital I/O lines, and 2-CH 32-bit general-purpose timer/counter. The auto-calibration functions adjust the gain and offset to be within specified accuracies such that you do not have to adjust trim pots to calibrate the cards.
-
VCIR -
RJS Technologies, Inc.
The Verifier Computer Interface Report (VCIR) is a Windows software package that allows for transferring inspection report from your Inspector series bar code verifier to a computer. Once transferred you can review the ISO/ANSI inspection results or view the scan reflectance profile for detailed troubleshooting. The inspection results can be saved by job for later retrieval or to append new inspection results to the existing job. As each job is saved an Excel spreadsheet (CSV file) is generated. You can customize which parameters should be saved in the spreadsheet. The spreadsheet provides a simple report that will have a line for each bar code inspected.
-
B-1020-C -
ROSS ENGINEERING CORPORATION
These supply 120V or 240V AC continuous power for equipment that must operate while at a high voltage to ground or power source. For example, a fiber optic transmitter at the HV level for waveforms to be received and measured or recorded by grounded instrumentation might be powered by an isolation transformer secondary to primary either insulated by potting, oil or air. The low dielectric constant of air insulation provides lower capacitive coupling between the secondary and the primary or ground than would solid or oil insulation. The lower capacitance provides better isolation both at line frequency and especially at high frequency voltages such as lightning or switching transients.
-
Mountz Inc.
Designed for industries where production errors simply aren't acceptable, Mountz preset torque screwdrivers apply the right amount of torque every time. Because they're locked into position by a torque analyzer and feature thrust load bearings to prevent end load interference, preset screwdrivers remove the possibility of operator error. Ideal for repeated production work like line assembly, Mountz preset screwdrivers with ergonomic handles reduce fatigue and protect workers from repetitive motion injuries. You can also protect your delicate electronics assemblies by using ESD-safe Mountz screwdriver models.
-
Nova ΙΙ 7Z01550 -
mks Ophir
*Compatible with all standard Ophir Thermopile, BeamTrack, Pyroelectric and Photodiode sensors.*Large, high definition LCD display.*Both digital and analog needle display.*USB and RS232 output to PC with Statistics package.*Select between English and Japanese interfaces*Analog output.*Soft keys and menu driven functions with on line help.*Log every data point at up to 4000Hz with pyroelectric sensors.*Non-volatile data storage up to 59,400 points.*Laser tuning screen and power log.*2 position kickstand.*System Integrator Tools included: LabVIEW VIs, COM Object Interface.
-
LAP GmbH
A glowing hot wire is pulled through the rolling mill at about 120 meters per second during ongoing production. Speed, high temperatures and dirt are special challenges for a high-precision measuring system. Our solution is the Contour Check Wire. It is specially designed for the geometric measurement of wires, rods and rebar and, at 800 Hz, offers the optimum measuring rate for accurate data acquisition. In the uniaxial version, you can check the diameter; in the two- to three-axis version, the ovality can also be determined. The small dimensions and light weight allow a quick and easy integration of the Contour Check Wire into the existing line.
-
HA5100 -
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA5100 series is a CATV booster optical amplifier with gain spectrum band within 1540~1563nm. This kind of optical amplifier is designed for the application of single channel or 1~8 continuous ribbon channels (ITU wavelength). Generally, fiber CATV system operates in single wavelength that has no strict requirement on gain flatness. HA5100 booster amplifier is featured with low NF, high-saturated output power. It is applicable for central bureau, sub-bureau and line relay, as well as other optical communication network. HA5100 is applied most commonly and widely compared with other optical amplifier in CATV system.
-
Quick Vision Active Series -
Mitutoyo Corporation
The Quick Vision Series comprises a family of CNC precision measuring machines equipped with an optical unit on which an image sensor is mounted. Non-contact measurement is performed by computer-processing the workpiece images. Since the first release in 1993, this series has been used in various industries including electrical and electronic, medical equipment and pharmaceutical, automotive, and machine parts, to name just a few. Mitutoyo has significantly contributed to quality and productivity improvements for those customers who use our CNC Vision Measuring Systems in measurement of precision parts on their production lines, especially when incorporated in semi-automatic inspection systems.
-
MiniMax™ -
Genmark Automation
Genmark’s MiniMax™ Equipment Front End Module (EFEM) is a class 1 minienvironment system designed to maximize productivity of semiconductor processing equipment tools that require the highest level of automation.The MiniMax™ can be customized to meet the automation requirements of any semiconductor manufacturing tool application and specified with one of the Genmark’s sophisticated and precise wafer and reticle handling robots, including the full line of patented GPR single or dual arm robots, GREX robot series, single and dual wafer aligners, FOUP/FOSB openers, reticle libraries, as well as any other customer specified equipment.
-
OPS-1000 -
Hangzhou Huatai Optic Tech. Co., Ltd.
OPS-1000 Optics Protection System product series, mainly applies to optical communication field of single fiber two-way for main, light path switching equipment. It makes up from light path switching unit, optical power monitoring unit and network management terminal. In optical communication networks, OPS-1000 real-time monitor the optical power of operating fibers and spare fibers, when monitor the optical light path’s optical power is lower than setting switching threshold, it will alarming prompt and switch to the spare fiber to realize the line protection of optical transmission system.
